FLUKE 8600A PDF

Model: A. Manufacturer: Fluke. About: We are NES Sales, Northeast’s industrial source. Notes: Does not include stand. Sold as-is, as pictured. | eBay!. Fluke A bench multimeter. «on: November 04, , am». I got this oldie from ebay the other day, the seller sold it as untested but it works. Fluke will not be liable for any claims, losses or damages of any kind incurred by any user arising from use of this manual. A Digital Multimeter Instruction.

Author: Nishicage Dougar
Country: Jordan
Language: English (Spanish)
Genre: Health and Food
Published (Last): 20 February 2013
Pages: 173
PDF File Size: 10.19 Mb
ePub File Size: 18.2 Mb
ISBN: 618-3-13549-958-2
Downloads: 8700
Price: Free* [*Free Regsitration Required]
Uploader: Akinozahn

Fluke 8600A Digital Multimeter

Improper opera- tion may not always be caused by flukf within the A. Printed Circuit Board Part Number f. A delay of 15 jusec is introduced in U8 between application of the read reference and the start of the counter.

This manual has not been edited or updated since the revision date shown on the lower left hand corner of the first page. A positive dc level at the converter will cause DOU output pin 3 to go to logic 1 and pin 5 A to go to logic 0. You can purchase with complete confidence that the equipment will be provided in excellent cosmetic operational condition.

The flkke capacitor is then discharg- ed at a controlled rate so that the discharge time is pro- portional to the level of charge on the capacitor. Now Rubbercraft Corp. When charging is complete, discharge the pack at the capacity-divided-by rate for 30 hours, then recharge at twice the discharge rate for a period of 20 hours.

  HANS PFAALL PDF

The distortion is introduced to minimize errors in small signal measurements caused by the turn-on time of CR Input Divider Test The Data Output Unit DOU provides digital measurement information to a rear panel output connector for use by remote display instruments or data printers.

Allow the battery pack to discharge for 30 hours, then charge the battery pack at twice the discharge rate for 20 hours. Learn More – opens in a new window or tab Any international shipping and import charges are paid in part to Pitney Bowes Inc. The voltage on both pins should be approximately —8.

Box Beijing Tel: Cleveland, OH Microsemi Corp. Minimum monthly payments are required. Q3 conducts an amount of current such that the voltage drop on R35 equalizes the input voltages on Pins 2 and 3 of U3. Locate the power selection switch; near the rear or the main pcb assembly. Connect the A to the appropriate 1 1 5V ac or V ac line power.

The read reference voltage applied to U4 allows U4 and U5 to dis- charge C Decimal point logic is a positive pulse output from U8 occuring at the same time as the appropriate strobe signal. The Modelas shown in Figureis a clamp-on current probe which is used to extend the current measurement capabilities of the A.

Rent Fluke A Digital Multimeter 4 1/2 Digit | Transcat

Return the ac signal source back to 3. The battery manufacturer recommends allowing the instrument to warm up to room temperature before charging the unit.

If the signal is distorted check the operation of Ql. Remove screw from rear of case and separate the case from the A. The 10V out of Ul is dropped across the input divider network. Using the dc 8600aa calibrator check Table 4- 1 for correct calibrator sequentially apply the values of dc current indicated in Table 44 to the A MA input terminals and select the ranges prescribed.

  GALLAHUE UNDERSTANDING MOTOR DEVELOPMENT PDF

Digital Multimeter 8600A

Troubleshooting information for the indicated fault area is presented in the following paragraphs. Back to home page Return to top. Model A Specifications 2- 1.

Remove the phillips screw from the rear of the instrument. Install the side mounting brackets, as shown in Figureand secure them to the mounting panel using the nuts provided. International Service Center Fluke Stock Number d.

The specifications for the Battery Pack are given in Section 1 of this manual. Clean the front panel and exterior surfaces with an- hydrous ethyl alcohol or a soft cloth dampened with a mild solution of detergent and water. Model A Outline Drawing 2- 1. Use the following procedure fluje check the power supply output voltages.

Full text of “FLUKE A Instruction”

Refer to figure and the timing diagram figure for the following discussion. Description of each part c. Typically, the battery will provide up to 1 hours of continuous operation before, replace- ment is necessary.

The input divider is used to change the amount of current applied to the un- known resistance when different ranges are selected.