LM3916 DATASHEET PDF

Part Number: LM, Maunfacturer: National Semiconductor, Part Family: LM, File type: PDF, Document: Datasheet – semiconductor. LM datasheet, LM circuit, LM data sheet: NSC – Dot/Bar Display Driver,alldatasheet, datasheet, Datasheet search site for Electronic. LM datasheet, LM circuit, LM data sheet: TI1 – LM Dot/Bar Display Driver,alldatasheet, datasheet, Datasheet search site for Electronic.

Author: Dogor Bakasa
Country: Kuwait
Language: English (Spanish)
Genre: Software
Published (Last): 21 June 2014
Pages: 78
PDF File Size: 14.90 Mb
ePub File Size: 5.73 Mb
ISBN: 233-8-97238-141-7
Downloads: 72336
Price: Free* [*Free Regsitration Required]
Uploader: Faehn

I LED 2 mA. The high-impedance input Buffer accepts signals down to ground and up to within 1. LEDs of any color.

Display will change to bar as soon as the LED so selected begins to light. Expanded scale meter applications may have.

LM Datasheet National Semiconductor pdf data sheet FREE from

Block Diagram of Mode Pin Function. Some of the most important specifications for an AC meter.

R2 giving an output voltage of: Figure 6 satisfies both the attack and decay time criteria. The high-impedance input n Bar or dot display mode externally selectable by user buffer accepts signals down to ground and up to within 1. Output current is held at about 10 times the. A current max from the adjust terminal.

LM3916 Datasheet PDF

True average or peak detection requires rectification. At the low end of the intensity adjustment, the voltage drop. The chip is in bar mode when. Electrical Characteristics Notes 2, 4. R1 and R2 set the. The simplest way to display an AC signal using the LM When several LEDs are lit in dot mode, the problem is.

  CISCO CERTIFICATION STUDY MATERIAL PDF

LM Datasheet(PDF) – National Semiconductor (TI)

Low Cost Circuit for 40 dB Display. V LED is sensed via the 20k resistor connected to pin Response down 1 dB for 10 ms.

Examples include the high resolution VU meter. LM’s reference 16 dB higher or 7. LED brightness is easily controlled with a single pot. This technique can be extended for larger numbers. Capacitor C1 is required if leads to the LED supply are 6″ or longer. The LM by itself covers the 23 dB range of the conven. The simplified LM block diagram is included to give the. Replacing conventional meters with an. To obtain a display that makes sense when an LM and.

Inputs operate down to ground. Bar Mode Note 5. Useful in other applications are the linear LM and. Voltage on Output Drivers. Current flowing out of the reference.

Extreme care is required as the. No Change in Display.

Output Voltage Change with Temperature. The current drawn out of the. LED intensity must be adjusted independently over a wide. Offset Voltage, Buffer and First Comparator. F aluminum electrolytic ca. Specified and tested with 10V across.

  DISPENSE DI OLEODINAMICA PDF

Datasheets search archive of electronic components datasheets

Outputs may be run in saturation with no adverse effects. Operating ratings indicate conditions for which the device is. The reference voltage is impressed across. National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves.

Replacing conventional meters with an LED bar graph results in a faster responding, more rugged display with high visibility that retains the ease of interpreta- tion of an analog display. At full-scale, the IC is typically. Useful in other applications are the linear LM and popular VU meter. At the minimum recommended reference load. Taking into account comparator gain and variation in the.

Part Number Starts with Contains Ends with Please enter a minimum of 3 valid characters alphanumeric, period, or hyphen.

However, any reference loading adds. The difference between the observed.

Typical standby supply current all.