LM R e Thin Film Resistor Network. 0 05% Matching and 5 ppm This datasheet has been download from: Datasheets for electronics components. On all operational amplifier data sheets, the specifications listed on the deep in the data sheet. .. , LM and LT with improved price/performance. LM Datasheet: LM Precision Operational Amplifier, LM PDF Download National ->Texas Instruments, LM Datasheet PDF, Pinouts, Data Sheet.
|Published (Last):||16 September 2015|
|PDF File Size:||1.6 Mb|
|ePub File Size:||16.69 Mb|
|Price:||Free* [*Free Regsitration Required]|
The LM has a Class B output, and will exhibit transients at the crossover point. Capacitance in the Typical Performance Characteristics section show graphically that a modest capacitance of 0. Datashet regulation is defined as the change in the output voltage at a time T after a step change of power dissipation of mW. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
The curves showing the Noise vs. This point occurs when the device is required to sink approximately 1. Contact the factory for availability of devices with proven long-term stability. The output is short-circuit-proof to ground.
Pin numbers for H, M or N packages. The datashee scheme is such that individual resistors are cut open rather than being trimmed pm607 cutto avoid resistor drift caused by electromigration in the trimmed datasheer.
The LM also provides excellent stability vs. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. The output can sink current as well as source it, but the output impedance is much better for sourcing current. Consult factory for availability of devices with tighter Accuracy and Tempco Specifications.
The output has a class-B stage, so if the load current changes from sourcing to sinking, an output transient will lm6607. This datasheet has been downloaded from: To avoid this transient, it may be advisable to preload the output with a few milliamperes of load to ground.
LM607 Datasheet PDF
These pins may be cut off if desired. Ceramic capacitors may seem to do the job, but are not recommended for production use, as the high-K ceramics cannot be guaranteed for low leakage, and may exhibit piezo-electric effects, converting vibration or mechanical stress into excessive electrical noise.
These limits are not to be used to calculate outgoing quality levels. Avoid such overloads for voltages higher than a 20 V, for more than 5 seconds, or, at high ambient temperatures. A trim pin is available which permits fine-trimming of Vout, and also permits filtering to greatly decrease the output noise by adding a small capacitor 0.
These pins would not be damaged by a short to ground, or by Electrostatic Discharges; however, keep them away from large transients or AC signals, as stray capacitance could couple noises into the output.
LM Datasheet(PDF) – DATASHEETBANK
Life support devices or systems are devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
Trimming to a wider range is possible, but is not recommended as it may degrade the Tempco and the Tempco linearity at temperature extremes. Changes in output voltage due to heating effects are covered under the specifications for Thermal Regulation and Tempco.
In some applications it may be advantageous to pre-load the output to either Vin or to ground, to avoid this crossover point. Consult factory for availability of devices with Guaranteed Long-term Stability. Do not connect anything to these pins, or improper operation may result. They are based on a buried zener reference as pioneered in the LM references, but do not require any heater, as they rely on special temperature-compensation techniques Patent Pending.
There is no guarantee that the Specified Temperatures are exactly at the minimum or maximum deviation. The trim pin pin 5 should also be guarded away from noise signals and leakages, as it has a sensitivity of 15 millivolts of DVout per microampere. The capacitor used should be a low-leakage type. LM see curve above: Unless otherwise noted, these conditions apply: The device does not include a thermal shut-down circuit. The LM is recommended for applications where the highest stability and lowest noise is required over the full military temperature range.
However, avoid overloads at high ambient temperatures, as a prolonged short-circuit may cause the junction temperature to exceed the Absolute Maximum Temperature.
The devices have a The LM is suitable for limited-temperature operation. Its long-term stability datashwet typically 3 to 10 ppm per hours when held near Tmax, and slightly better when operated at room temperature.
Documents Flashcards Grammar checker. In Sinking mode, connect 0.